A two-component waterborne urethane wood floor finish formulated for interior use on heavy traffic residential and commercial wood floors. BonaKemi's most chemical-resistant, two-component finish.

---

FEATURES:

• Provides an extremely tough, high-build urethane finish
• Natural wood color- enhances the soft grain in the wood
• Excellent chemical and scuff resistance
• Easy to maintain
• Available in gloss, semi-gloss or satin
• VOC compliant–VOC does not exceed 350 grams per liter
• Fast drying–1-2 hours
• Virtually odorless
• Nonflammable
• Water cleanup
• Will adhere to most finishes after proper preparation and dry times

---

RECOMMENDED USES:

• Heavy traffic residential-kitchens, entry ways, family rooms, homes with pets, children and heavy foot traffic
• Commercial- restaurants, offices, retail stores
• Institutional applications - hospitals, nursing homes, schools
• Not recommended on white or pastel stained floors

---

DIRECTIONS FOR USE:

PACIFIC ULTRA™ brand floor finish provides an extremely tough, high-build urethane finish for residential and commercial floors with heavy traffic. PACIFIC ULTRA™ provides a deep, rich finish with a “traditional look.” PACIFIC ULTRA™ provides superior chemical resistance, protecting against most household chemicals. PACIFIC ULTRA™ is the Environmental Choice. The Environmental Choice® Seal is a registered trademark of BonaKemi USA, Inc. and represents a waterbased formula which meets or exceeds all state and federal clean air quality standards. Available in gloss, semi-gloss and satin.

BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET #80170 FOR THIS PRODUCT AND MSDS #80050 OR #50080 FOR THE CROSSLINKER.

PREPARATION: ABRADE AND RECOAT OLD FLOORS
1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with Bona Swedish Formula Hardwood Floor Cleaner. 3. Abrade with Bona Conditioning Pad. 4. Vacuum thoroughly. 5. Tack with slightly water-dampened cloth or Bona Mop. 6. Apply finish (see finish directions).

NOTE: PACIFIC ULTRA will adhere to most stains and finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY.

SANDING AND FINISHING NEW FLOORS 1. Sand floor using NOFMA-accepted methods. 2. For a neutral or stained floor, make your final cut with 80-grit paper and screen with 80-100-grit screen. Apply BONA WOODLINE DS-STAIN. For an unstained, natural floor, make your final cut with 100-grit paper and screen to 150 grit. This burnishing will reduce the amount of grain raise. 3. Vacuum thoroughly. 4. Tack with slightly water-dampened cloth. 5. Apply sealer and finish system (see finish directions).

THE PACIFIC ULTRA™ SYSTEM IS A 3-COAT SYSTEM:

• 1 coat of BONA PACIFIC HIGH BUILD–The use of HIGH BUILD SEALER minimizes the possibility of sidebonding.
• 2 coats of PACIFIC ULTRA™. Adding a third coat of finish is recommended in high traffic commercial and residential areas.

NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.

INTERCOAT ABRASION: Abrading between finish coats is not necessary for adhesion unless it has been more than 48 hours since the previous coat has been applied. However, for smoothest floor results, buff the sealer coat with a BONA Conditioning Pad and two BONA SIAFAST Delta Sheets. The Delta Sheets are to be used for abrading Pacific High Build only. Prior to applying the final finish coat, buff with the Bona Conditioning Pad. Always thoroughly vacuum and tack with a slighly water-dampened cloth after buffing.

FINISHING: SHAKE OR STIR WELL BEFORE USING. 1. Open the crosslinker bottle and add an equal part of water to the crosslinker. Shake well. Add the crosslinker/water mixture to PACIFIC ULTRA within 15 minutes. Shake or stir and let sit 5-10 minutes. 2. Using a plastic pour can, pour a 4" wide line of finish along the starting wall. Go with the grain of the wood. 3. Using a clean, pre-dampened applicator, draw the applicator forward, with the grain of the wood, moving the finish toward the opposite wall. By holding the applicator at a "snowplow" angle, it maintains a wet edge at all times. 4. At the end of each stroke, turn the applicator toward you and pad out the applicator parallel to the wet edge. 5. Feather out all turns. If pushed too hard or too fast, drips will fly off the applicator. 6. Missed areas can be touched up if seen right away. 7. To prevent lapping and dry marks, be sure you are using the recommended coverage of 500-600 sq. ft. per gallon. Be careful not to spread the finish too thin. 8. Allow your first coat to dry 1-2 hours. For smoothest results, before applying final coat, buff with BONA Conditioning Pad. Vacuum and tack thoroughly before applying final coat. Allow final coat to dry at least 48 hours before use.

CURING: The curing process takes approximately 7 days. Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Cleaning with water or detergent is not allowed during the first week.

CLEAN-UP: Tools should be cleaned with water and stored in the BONA Applicator Storage Canister.

MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit. Sweep or vacuum daily and damp wipe as needed with BONA Swedish Formula Hardwood Floor Cleaner. The floor may be periodically spray-buffed with cleaner and a white polishing pad to clean larger areas.

SPECIFICATIONS/PHYSICAL DATA:
Physical Characteristics:
Ingredients - Water, polyurethane/acrylic polymer dispersions, Diethylene Glycol Monomethyl Ether, N-Methyl-2-Pyrrolidone, defoaming and leveling additives
Color - Off white (wet)
pH - 7.9
Solids - 32.5%
Viscosity - (#4 Ford cup @ 25° C) 21 seconds
Packaging - 1-gallon plastic bottle. Comes complete with crosslinker.
Gloss Level - (60°) >90 for gloss, 55 for semi-gloss, 40 for satin
Odor - Non-offending
Flash Point - >200° F
Density - 8.75 Ibs./gallon (1.05 S.G.)
VOC Compliant - Does not exceed 350 grams per liter (2.9 lbs. per gallon)
Storing Durability - 1 year shelf life

Application Characteristics:
Clarity - Clear when dry
Leveling - Excellent
Defoaming - Excellent
Drying Time - 1-2 hours
Coverage - 500-600 square feet per gallon
Percent Cured After 24 Hours - 70%
Maximum Cure - 100% after one week
Application Tools -Bona Brush, flocked foam Bona Swivel Head Floor Coater applicator, Bona Swedish roller
Pot Life - The finish/crosslinnker mixture is active for 8 hours after it is mixed. Within 2-3 days, crosslinker may be added one additional time.